Put my first coat of bondo on the rear fender areas and gave it a first sand and then a 2nd coat of bondo for an overnight cure.
Did my last body repair weld on the rear fender inner rail as it got cut out earlier.
Then I ground down the spot welds on the firewall to make clear the path for the firewall from my Camo Rig.
Just a few more steps and she'll be ready for paint!
Monday, 14 December 2015
Friday, 11 December 2015
Odds and ends...
Little bit more accomplished today...
1. Slapped some primer on the lower tailgate repair (bottom 3"). Will need to sand and bondo a couple areas before it's ready for real paint.
2. Removed a few brackets, cleaned them up and sprayed them with some black. Not sure how that will look in the end with black brackets, but I think they will "pop" a bit with the grey paint in the end. We'll see.
3. Took every single screw/bolt out that is inside the cab or holding a door or WHY, put each one through a thread repair and reinstalled with anti-seize. The thread repair tool is NOT a cutting tool, but simply removes any rust or nicks on the threads. Let's just say each bolt threaded in by hand after I was done. Bam!
4. Removed the rear quarter panel uprights in anticipation of building storage access panels similar to Wagongear's. Figured I already had the spot weld drill out, so out they came...pop. Really nice and open without those "braces."
5. Finished the GT Mat on the ceiling. Much easier than the floor because there are no rolling divets. However, gravity sometimes didn't like it as I'm working in the cold so a bit of heat and things seemed to hold. Lots of seam tape pretties things up too.
6. Seam sealed the rear inner quarters where I fabbed new outer fenders and did the rear quarter chop. Still left the bottoms open with a few holes so as to allow moisture to escape.
7. Removed the overhead roof support and cleaned it up. Gonna paint it black. Probably won't even see it in the end because, well, I have something brewing of an idea that would make it disappear.
8. And lastly, fished in an orange pull string for when I pull my original wiring harness back into this rig!
Seam sealer
Got around to sealing things up this week.
- Gutter/rails
- Floors
- Window runners
- Patches/weld repair spots
- You know, places that need to be sealed up!
Also hit the inner rear fender wells with some asphalt spray stuff...seems legit.
- Gutter/rails
- Floors
- Window runners
- Patches/weld repair spots
- You know, places that need to be sealed up!
Also hit the inner rear fender wells with some asphalt spray stuff...seems legit.
Saturday, 5 December 2015
Rear Cargo Weatherstripping Frame Rail Repair
There was a bit of rust along the frame rail that I noticed when I removed the weatherstripping so I figured tonight would be a good time to cut it out and weld in a new piece. Still some seam sealer to install, but that's about it. Ready for paint!
Inner Fender Well Repairs
Notoriously bad, these inner fenders seem to hold moisture, so cutting out any bad areas and replacing with new is well worth it at this stage in the game.
Still seam sealer to install, then Dynamat throughout interior (GT Mat...knockoff brand).
Still seam sealer to install, then Dynamat throughout interior (GT Mat...knockoff brand).
Rear Quarter Chop: Stage 2
Today I got around to (mostly) finishing welding up the rear quarter chop pieces into place.
Still need to figure out outter fender repairs and how those will tie in.
Also the underside (inner) of the chop needs to be sealed and possibly trimmed so less debris can hang out there.
Then a bit of bondo, sanding and paint 'em up!
Still need to figure out outter fender repairs and how those will tie in.
Also the underside (inner) of the chop needs to be sealed and possibly trimmed so less debris can hang out there.
Then a bit of bondo, sanding and paint 'em up!
Subscribe to:
Posts (Atom)



















































